INBOARD ENGINE MANUAL
INBOARD ENGINE PROFESSIONAL

Finally, remove the flusher and disconnect the garden hose. Don’t leave the engine running without water. If at any point the temperature goes over 200 Fahrenheit, immediately switch off the ignition. In addition, you should check the temperature gauge. Water should exit constantly through the exhaust. While the engine is running, keep an eye on the muff plunger to ensure it doesn’t fall off. Also, this will help flush out the debris and residues that might have accumulated during winterization. Leave the engine on for four to five minutes to make sure it works perfectly. Now that all is set, it’s safe to start the engine. Turn on the water supply and you should see water pouring down the flusher.

Step 4: Pump water to the engine while the boat motor is running

The water hole must be covered entirely and the muff must cling on tightly so it won’t slide when high water pressure is established. Adjust the leg height as needed and secure it firmly against the ground. Step 3: Set up the plungerĬover the intake hole with the muff plunger.

INBOARD ENGINE MANUAL

Otherwise, check the manual instructions. Go underneath and you shall see it near the boat motor. You need to locate the vessel water intake. Step 2: Determine where the engine gets water Turn the water on to check if there are leaks. Ensure the hose is tight enough to withstand high pressure of water. Step 1: Attach the motor flusher to the garden hoseĬonnect the garden hose to the outlet attachment. Remember that water will be pumped out of the vessel engine don’t try to run an inboard boat out of water in your garage. With that said, start off by parking your boat in a flat, open area, and mount it on the trailer. No worries though! As long as you pay close attention while working and turn off the engine in time, no damage will be caused.

INBOARD ENGINE PROFESSIONAL

When anything appears to be out of ordinary, immediately turn the engine off and ask for professional help. There should be no alarm or red blink on the monitor board. Under ten seconds or so, the impeller has a bigger chance to survive.Īfter that, move your vessel back on the water and start the engine to see if it runs smoothly. If something went wrong with the water supply when the motor is running, turn the ignition off as soon as possible. It only takes a quick ten seconds of the motor’s running on dry land to damage it severely. The cooling system needs running water to lubricate and cool down the engine. Please be aware that running a boat engine out of water without any source of water supplies can be fatal to the impeller. Steps to Run an Inboard Boat Out of Water Also, check for leaks on the hose, making sure it works properly. Any garden hose will work as long as it fits the outlet attachment of the flusher. You will need a garden hose to supply water. Besides helping with starting a boat out of water, a motor flusher will assist in regular engine cleaning. You can easily buy one at your local Walmart or on Amazon. Once started, the constant supplies of water will run through the vessel engine.

The plunger will cover the water intake hole on your vessel, assuring water gets into the motor. The outlet attachment will allow the flusher to connect with a garden hose. Basically, it looks like a toilet plunger and has the same operating principle. Don’t mistake it as an inboard engine flusher.Īn inboard engine flusher is sometimes called a circular plunger. The other side is attached to the engine’s inlet vents and sucks water out of it. One side is connected to the water supply, then to the boat intake hole and pumps water into the engine. An inboard motor flusherĪn outboard motor flusher looks like an earmuff. If you own an outboard motor, the procedure to start it out of water is different. Nowadays, outboard engines are more popular due to their increased power control, lower risks of fire hazards, and more affordable prices. Meanwhile, an outboard motor is installed outside the vessel, typically at the back. As said in the name, an inboard motor is mounted inside the vessel, usually at the hull area. To be clear, we are providing information on starting an inboard engine, not an outboard one. Step 4: Pump water to the engine while the boat motor is running.Step 2: Determine where the engine gets water.Step 1: Attach the motor flusher to the garden hose.Steps to Run an Inboard Boat Out of Water.

Inboard engine